-
1 symmetry tolerance
допуск симметричности
1) Допуск в диаметральном выражении - удвоенное наибольшее допускаемое значение отклонения от симметричности.
2) Допуск в радиусном выражении - наибольшее допускаемое значение отклонения от симметричности
Допуск симметричности рекомендуется указывать в диаметральном выражении
[ ГОСТ 24642-81]Тематики
Обобщающие термины
EN
DE
FR
Англо-русский словарь нормативно-технической терминологии > symmetry tolerance
-
2 symmetry tolerance
English-Russian big polytechnic dictionary > symmetry tolerance
-
3 symmetry tolerance
1) Техника: допуск на симметрию2) Механика: допуск симметричности -
4 symmetry tolerance
Англо-русский словарь по машиностроению > symmetry tolerance
-
5 symmetry tolerance
English-Russian dictionary of mechanical engineering and automation > symmetry tolerance
-
6 symmetry tolerance zone
поле допуска симметричности
Область в пространстве, ограниченная двумя параллельными плоскостями, отстоящими друг от друга на расстоянии, равном допуску симметричности в диаметральном выражении T или удвоенному допуску симметричности в радиусном выражении T/2, и симметричная относительно базовой плоскости симметрии или базовой оси.
[ ГОСТ 24642-81]Тематики
Обобщающие термины
EN
DE
FR
Англо-русский словарь нормативно-технической терминологии > symmetry tolerance zone
-
7 symmetry tolerance zone
Автоматика: поле допуска симметричностиУниверсальный англо-русский словарь > symmetry tolerance zone
-
8 symmetry tolerance zone
English-Russian dictionary of mechanical engineering and automation > symmetry tolerance zone
-
9 tolerance
- angularity tolerance
- axial runout tolerance
- balance tolerance
- basic tolerance
- bilateral tolerance
- blade angle tolerance
- blueprint tolerance
- bottom tolerance
- camming action tolerance
- capacitance tolerance
- circular runout tolerance
- circularity tolerance
- close tolerance
- coaxiality tolerance
- composite tolerance
- concentricity tolerance
- cone angle tolerance
- cone diameter tolerance
- cone section diameter tolerance
- contamination tolerance
- cumulative tolerance
- cylindricity tolerance
- design tolerances
- diameter tolerance
- diametric tolerance
- dimensional tolerance
- established tolerance
- exacting tolerance
- fault tolerances
- fine tolerance
- fit tolerance
- flatness tolerance
- form tolerance
- functional tolerances
- gear-mounting tolerance
- gear-spacing tolerance
- geometric tolerance
- high tolerance
- holding tolerances
- inclusive tolerance
- index tolerance
- in-line tolerance
- international tolerance
- intersection tolerance
- lead tolerance
- limit tolerance
- line profile tolerance
- location tolerance
- lower tolerance
- machining tolerance
- manufacturing tolerance
- maximum-material-condition tolerance
- micron tolerance
- MMC tolerance
- nonqualified tolerance
- parallelity tolerance
- part-to-part tolerances
- perpendicularity tolerance
- pitch tolerance
- positional tolerance
- positioning tolerance
- precision tolerance
- press-fit tolerance
- print tolerance
- process tolerance
- production tolerance
- profile tolerance of any line
- profile tolerance of any surface
- profile tolerances
- qualified tolerance
- radial runout tolerance
- regardless-of-feature-size tolerance
- repeatability tolerance
- repetitive tolerance
- rough tolerance
- roundness tolerance
- run tolerance
- runout tolerance
- setup tolerances
- size tolerance
- specified tolerance
- straightness tolerance
- surface profile tolerance
- symmetry tolerance
- target tolerance
- targeted tolerance
- thread tolerance
- tight tolerance
- tolerance of position
- tolerance of positioning
- tolerance of runout
- top tolerance
- total composite tolerance
- total radial runout tolerance
- total runout tolerance
- true-position tolerance
- two-line tolerance
- unbalance tolerance
- unilateral tolerance
- upper tolerance
- wide tolerance
- Z-axis tolerance
- zero toleranceEnglish-Russian dictionary of mechanical engineering and automation > tolerance
-
10 tolérance de symètrie
допуск симметричности
1) Допуск в диаметральном выражении - удвоенное наибольшее допускаемое значение отклонения от симметричности.
2) Допуск в радиусном выражении - наибольшее допускаемое значение отклонения от симметричности
Допуск симметричности рекомендуется указывать в диаметральном выражении
[ ГОСТ 24642-81]Тематики
Обобщающие термины
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > tolérance de symètrie
-
11 zone de tolérance de symètrie
поле допуска симметричности
Область в пространстве, ограниченная двумя параллельными плоскостями, отстоящими друг от друга на расстоянии, равном допуску симметричности в диаметральном выражении T или удвоенному допуску симметричности в радиусном выражении T/2, и симметричная относительно базовой плоскости симметрии или базовой оси.
[ ГОСТ 24642-81]Тематики
Обобщающие термины
EN
DE
FR
Франко-русский словарь нормативно-технической терминологии > zone de tolérance de symètrie
-
12 допуск симметричности
Русско-английский исловарь по машиностроению и автоматизации производства > допуск симметричности
-
13 tolleranza
"tolerance;Toleranz"* * *f tolerance* * *tolleranza s.f.1 tolerance; ( indulgenza) indulgence: il nostro governo ha sempre dato prova di grande tolleranza, our government has always shown great tolerance; avere tolleranza per il freddo, il caldo, to be able to stand (o to tolerate) the cold, the heat; la tolleranza dell'organismo a un medicinale, the tolerance of an organism to a medicine; avere spirito di tolleranza, to be tolerant; giudicare con tolleranza, to be tolerant in one's judgement; tolleranza politica, religiosa, political, religious tolerance // casa di tolleranza, brothel2 ( capacità di sopportare il male) endurance, tolerance, stamina3 (comm.) ( scarto) allowance: tolleranza sul peso, sul calo delle merci, allowance on the weight, on the loss of weight of goods4 ( limite, margine) margin, leeway, tolerance: fissare un orario con una tolleranza di 20 minuti, to set a time with 20 minutes leeway; una tolleranza di quindici minuti, a fifteen minute tolerance; (banca) giorni di tolleranza, ( per il pagamento di cambiali) days of grace; (fin.) tolleranza di coniazione, coinage tolerance5 (tecn.) tolerance; ( di accoppiamento) allowance: tolleranza di forma, form tolerance; tolleranza di posizione, position (al) tolerance; tolleranza di simmetria, symmetry tolerance; tolleranza stretta, close tolerance; limite di tolleranza superiore, inferiore, high, low tolerance limit.* * *[tolle'rantsa]sostantivo femminile1) (apertura, rispetto) broadmindedness, tolerance2) (a medicinali, alcol, freddo) tolerance3) (tempo)con una tolleranza di dieci minuti — with a ten-minute margin o tolerance
* * *tolleranza/tolle'rantsa/sostantivo f.1 (apertura, rispetto) broadmindedness, tolerance; tolleranza religiosa religious toleration2 (a medicinali, alcol, freddo) tolerance -
14 допуск симметричности
допуск симметричности
1) Допуск в диаметральном выражении - удвоенное наибольшее допускаемое значение отклонения от симметричности.
2) Допуск в радиусном выражении - наибольшее допускаемое значение отклонения от симметричности
Допуск симметричности рекомендуется указывать в диаметральном выражении
[ ГОСТ 24642-81]Тематики
Обобщающие термины
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > допуск симметричности
-
15 поле допуска симметричности
поле допуска симметричности
Область в пространстве, ограниченная двумя параллельными плоскостями, отстоящими друг от друга на расстоянии, равном допуску симметричности в диаметральном выражении T или удвоенному допуску симметричности в радиусном выражении T/2, и симметричная относительно базовой плоскости симметрии или базовой оси.
[ ГОСТ 24642-81]Тематики
Обобщающие термины
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > поле допуска симметричности
-
16 симметричность
закон симметричности; закон симметрии — symmetry law
-
17 симметричность
закон симметричности; закон симметрии — symmetry law
Русско-английский словарь по информационным технологиям > симметричность
-
18 допуск симметричности
допуск симметричности
1) Допуск в диаметральном выражении - удвоенное наибольшее допускаемое значение отклонения от симметричности.
2) Допуск в радиусном выражении - наибольшее допускаемое значение отклонения от симметричности
Допуск симметричности рекомендуется указывать в диаметральном выражении
[ ГОСТ 24642-81]Тематики
Обобщающие термины
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > допуск симметричности
-
19 поле допуска симметричности
Русско-английский исловарь по машиностроению и автоматизации производства > поле допуска симметричности
-
20 zone
зона; область- active zone of the tool
- allowable zone
- alloyed melt zone
- alloying zone
- buffer zone
- chip-contact zone
- circularity tolerance zone
- coaxiality tolerance zone
- combustion zone
- constraint zone
- contact zone
- control zone
- cooling zone
- cutting zone
- cylindricity tolerance zone
- danger zone
- dead zone
- diffusion zone
- dual work zones
- examination zone
- explosion hazard zone
- flatness tolerance zone
- focal spot fusion zone
- forbidden zone
- fusion zone
- gaging zone
- heat-affected zone
- interference-free zone
- light-to-dark transition zone
- machining zone
- measuring zone
- neutral zone
- probe trip zone
- programmable safety zone
- projected tolerance zone
- proportional control zone
- safe working zone
- shaping zone
- shear zone
- symmetry tolerance zone
- tolerance zone of form
- tolerance zone of position
- tolerance zone of thread
- tolerance zone
- tool zone
- uncertainty zone
- weakened zone
- work zone
- working zone of the machine
- working zone
- workpiece zone
- Y/Z collision zone
- zone of action
- zone of instabilitty conditionEnglish-Russian dictionary of mechanical engineering and automation > zone
- 1
- 2
См. также в других словарях:
symmetry tolerance — leidžiamoji simetriškumo nuokrypa statusas T sritis Standartizacija ir metrologija apibrėžtis Dvipusis arba vienpusis didžiausias leidžiamasis simetriškumo nuokrypis, atitinkamai išreiškiamas leidžiamuoju skersmens arba spindulio nuokrypiu.… … Penkiakalbis aiškinamasis metrologijos terminų žodynas
tolérance de symétrie — leidžiamoji simetriškumo nuokrypa statusas T sritis Standartizacija ir metrologija apibrėžtis Dvipusis arba vienpusis didžiausias leidžiamasis simetriškumo nuokrypis, atitinkamai išreiškiamas leidžiamuoju skersmens arba spindulio nuokrypiu.… … Penkiakalbis aiškinamasis metrologijos terminų žodynas
Symmetrietoleranz — leidžiamoji simetriškumo nuokrypa statusas T sritis Standartizacija ir metrologija apibrėžtis Dvipusis arba vienpusis didžiausias leidžiamasis simetriškumo nuokrypis, atitinkamai išreiškiamas leidžiamuoju skersmens arba spindulio nuokrypiu.… … Penkiakalbis aiškinamasis metrologijos terminų žodynas
leidžiamoji simetriškumo nuokrypa — statusas T sritis Standartizacija ir metrologija apibrėžtis Dvipusis arba vienpusis didžiausias leidžiamasis simetriškumo nuokrypis, atitinkamai išreiškiamas leidžiamuoju skersmens arba spindulio nuokrypiu. atitikmenys: angl. symmetry tolerance… … Penkiakalbis aiškinamasis metrologijos terminų žodynas
допуск симметричности — leidžiamoji simetriškumo nuokrypa statusas T sritis Standartizacija ir metrologija apibrėžtis Dvipusis arba vienpusis didžiausias leidžiamasis simetriškumo nuokrypis, atitinkamai išreiškiamas leidžiamuoju skersmens arba spindulio nuokrypiu.… … Penkiakalbis aiškinamasis metrologijos terminų žodynas
допуск симметричности — 1) Допуск в диаметральном выражении удвоенное наибольшее допускаемое значение отклонения от симметричности. 2) Допуск в радиусном выражении наибольшее допускаемое значение отклонения от симметричности Допуск симметричности рекомендуется указывать … Справочник технического переводчика
поле допуска симметричности — Область в пространстве, ограниченная двумя параллельными плоскостями, отстоящими друг от друга на расстоянии, равном допуску симметричности в диаметральном выражении T или удвоенному допуску симметричности в радиусном выражении T/2, и… … Справочник технического переводчика
Geometric dimensioning and tolerancing — (GD T) is a system for defining and communicating engineering tolerances. It uses a symbolic language on engineering drawings and computer generated three dimensional solid models for explicitly describing nominal geometry and its allowable… … Wikipedia
Life Sciences — ▪ 2009 Introduction Zoology In 2008 several zoological studies provided new insights into how species life history traits (such as the timing of reproduction or the length of life of adult individuals) are derived in part as responses to… … Universalium
literature — /lit euhr euh cheuhr, choor , li treuh /, n. 1. writings in which expression and form, in connection with ideas of permanent and universal interest, are characteristic or essential features, as poetry, novels, history, biography, and essays. 2.… … Universalium
liquid crystal — a liquid having certain crystalline characteristics, esp. different optical properties in different directions when exposed to an electric field. [1890 95] * * * Substance that flows like a liquid but maintains some of the ordered structure… … Universalium